What are the Impurities Present in Wool? How They can be Removed?

Impurities in Wool and These Removing Process
Anju Singh
Pursuing M.Sc. in Fabric and Apparel Science
Delhi University, India
Email: anjusingh292@gmail.com





Introduction:
Raw wool contains 40% or more by weight of impurities in the form of waxes, suint, cellulosic material such as straw and dried grass, dirt, and proteinaceous material. Besides, during spinning and weaving other impurities are added.

1. Wool waxes are recovered from the grease during scouring. These waxes are comprised of a variety of monocarboxylic, dicarboxylic and hydrocarboxylic acids as well as steroidal alcohols. It has been determined that unscoured wool contains an unoxidized fraction of wool grease and other contaminants that is easily removed and readily recoverable and an oxidized fraction at the tip of the hair that is difficult to remove and separate from other oxidized contaminants.

2. Suint is usually considered to be a variable composition of water-soluble materials that is readily removed by scouring.

3. The dirt that is removed from the scoured wool consist of both inorganic and organic materials

4. The proteinaceous material has recently been discovered to consist of skin flakes from the sheep and soluble peptides.

The process that can remove the impurities has various steps:
(i) Wetting
(ii) Crabbing
(iii) Scouring
(iv) Carbonizing
(v) Milling
(vi) Bleaching

(i) Wetting: The first treatment given to wool is wetting. This treatment releases latent strains and gives permanent set provide, wet treatment is not done at temperatures higher than that used in crabbing.

(ii) Crabbing: This treatment is given to woolens to eliminate the tendency to cockle or distort. The wool is wound tightly on a roll which is made up of iron. The roll is a perforated cylinder covered with cotton cloth in order to prevent staining. It is rotated during treatment. Steam is passed in the cylinder at 40-150 lb/inch square pressure (as and when required). Now the wool is unwound and rewound, so that the outer roll of wool after crabbing becomes the inner roll, and steam is passed again, steaming enhances affinity of wool for dyes. The pH value of crabbing water determines the setting of wool. A low pH produces little setting and maximum degree of setting is attained at pH 10.2.

(iii) Scouring: Scouring of wool differs from cotton. Firstly, wool contains a high percentage (30-60%) of wool grease compared with 0.5% of oil and wax in cotton. Secondly, wool is degraded rapidly with alkali, hence it saponification of oils, and fats is to be done with alkali; it should be done very carefully and below the boiling temperature. Sodium hydroxide is replaced by sodium carbonate, ammonia or ammonium carbonate. Raw wool is scoured by the counter current method, using a machine with four or five bowls arranged in a sequence, so that the wool passes directly out of the first into second and so on. Each bowl has a wringer at the exit, a false bottom and rakes. Below the false bottom is a spirally fluted shaft which rotates and carries the deposited solid dirt to the central outlet for discharge. The rakes make the wool travel forward, beneath the surface of liquor and also agitate to keep the dirt and emulsified grease in suspension. The scouring liquor falls back in the bowl after the wool passes through the wringer. The process is repeated at each bowl. Finally it is washed in water.

Soap in solution      
sodium carbonate     
temperature
First bowl                              
2-3%
3-4%                        
49-52°C
Second bowl                 
1-3%                               
2-3%                        
46-49°C
Third bowl                    
1-1.5%                            
1-2%                     
43-46°C
Fourth bowl                 
water only                       
-
40.5-43°C
 
The pH should never be above 10. Soap reacts with hard water and precipitates calcium and magnesium salts, hence they have been replaced by synthetic detergent, and moreover syndents are more Gardinol and Teepol. There are stable to hard water and acids and are not used up ay all during scouring and can be reused. Moreover some pressure on wet wool in presence of soap can felt it which is not desirable.

Synthetic detergent   
sodium carbonate     
common salt
pH
temp
First bowl                              
0.25%                    
0.25%                        
-
9.0         
54°C
Second bowl                 
0.2%                       
0.2%                        
0.4%          
10-10.5     
52°C
Third bowl                    
0.12%                   
0.02%                       
0.5%             
10           
49°C
Fourth bowl                 
0-0.1%                    
0
0
-
46°C
 
After every 1000 lb of 454 kg of wool have passed over, the bowl should be fortified. Woven piece goods and knitted wool fabrics are sewn together to form an endless rope. These contain much less fats etc. and scoured with 0.5% soap solution or surfactant at 40°C. If alkali is required, ammonia is preferred.

(iv) Carbonizing (removal of burrs): Burr is mainly cellulosic material. Some cellulosic materials which form burr on the animal have to be removed. The method consists of hydro extracting with 6-8% H2SO4 then drying at 60-70°C, heating at 105-110°C and finally raising the temperature to 150°C.

After carbonizing fabric is passed through milling machine when hydrocellulose and hemicelluloses falls down, thus removing all vegetable impurities from wool.

(v) Milling: - it is done after or before dying process of milling is based on proper of wool, that when it is wet and subjected to pressure it felts permanently specially in presence of soap, alkali and acid. Felting gives denser or more durable fabrics of more pleasing appeal. Milling can be of three different types: soap, grease, and acid.

(vi) Bleaching: Yellowish color on the fabric may be removed only if the goods are to be sold as white or light colors where as for dark colors are washed by dye. Bleaching can be done by
  • SO2 – It is a cheep process knows as staving. In this case sulphur is burnt in chambers where the wool is hanging in loop form on wooden poles. Sulphur forms sulphur dioxide which acts on the yellow coloring matter. 
  • Hydrogen peroxide- It gives a better white light out. Fabrics are treated in winch machine i.e. without tension. Hydrogen peroxide contains acid for preservation hence sodium silicate is added to neutralize. (i.e. it acts as buffer to stabilize). Hydrogen peroxide is heated to 40-50°C. The materials are left overnight in the bleach liquor for complete bleaching wash the fabric with water and then with dilute acetic acid, again wash with water. This is preferred to staving. Heavy weight woolens are given this treatment on a jigger machine. Cloth is rolled on rollers A and B, roller C can be shifted from roller A and B squeezing. Cloth moves from A to B a number of times.
Jigger washing is done (by changing the bath) then wool is dried. When bleaching is done on jigger machine the strength of H2O2 should be 4-5 times higher than for light out fabrics as on a winch machine.

0 comments:

Comment here

Textile Learner is the largest Textile Blog over the net. It is an ultimate reference for textile students. It describes textile articles in comprehensive. It also supplies news on latest textile technology, educational institute news of the world.